Logo der Physikalisch-Technischen Bundesanstalt

Druck

Arbeitsgruppe 3.33

Eine Übersicht über die bisherigen Veröffentlichungen der Arbeitsgruppe Druck:

J. Könemann, S. Ehlers, M. Jescheck und W. Sabuga
The Mercury Micromanometer at PTB, In: Proc. of 5th CCM Pressure Metrology & 4th IMEKO TC16 Int. Conf., Berlin, May 2–5, 2011
2011, PTB-Mitteilungen 121: S. 303-306
W. Sabuga, F. Sharipov und T. Priruenrom
Determination of the effective area of piston-cylinder assemblies using a rarefied gas flow model, In: Proc. of 5th CCM Pressure Metrology & 4th IMEKO TC16 Int. Conf., Berlin, May 2–5, 2011
2011, PTB-Mitteilungen 121: S. 260-262
W. Sabuga, T. Priruenrom, R. Haines und M. Blair
Design and evaluation of pressure balances with 1*10-6 uncertainty for the Boltzmann constant project, In: Proc. of 5th CCM Pressure Metrology & 4th IMEKO TC16 Int. Conf., Berlin, May 2–5, 2011
2011, PTB-Mitteilungen 121: S. 256-259
K. Dapkeviciene, W. Sabuga, B. Waller, P. Farar, Y. Kiselev, K. Saczuk und I. Sandu
Final report on regional key comparison COOMET.M.P-K2: Hydraulic gauge pressure in the range 10 MPa to 100 MPa, Tech. Suppl., 07010
2011, Metrologia 48
I. Kocas, W. Sabuga, M. Bergoglio, A. El-Taweel, C. Korasie, P. Farar, J. Setina und B. Waller
EURAMET Key Comparison for 500 MPa Range of Hydraulic Gauge Pressure (EURAMET.M.P-K13), In: Proc. of 5th CCM Pressure Metrology & 4th IMEKO TC16 Int. Conf., Berlin, May 2–5, 2011
2011, PTB-Mitteilungen 121: S. 291-293
W. Sabuga
Pressure measurements in gas media up to 7.5 MPa for the Boltzmann constant redetermination, in Proc. of 5th CCM Pressure Metrology & 4th IMEKO TC16 Int. Conf., Berlin, May 2–5, 2011
2011, PTB-Mitteilungen 121 (3): S. 247-255
B. Fellmuth, J. Fischer, C. Gaiser, O. Jusko, T. Priruenrom, W. Sabuga und T. Zandt
Determination of the Boltzmann constant by dielectric-constant gas thermometry
2011, Metrologia 48: S. 382–390
W. Sabuga, P. Ulbig und A. D. Salama
Elastic constants of pressure balances' piston-cylinder assemblies measured with the resonant ultrasound spectroscopy
2010, Proceedings of the International Metrology Conference CAFMET-2010, Cairo
O. Jusko, D. Bastam, M. Neugebauer, H. Reimann, W. Sabuga und T. Priruenrom
Final Results of the Geometrical Calibration of the Pressure Balances to be Used for the new Determination of the Boltzmann Constant
2010, Key Engineering Materials 437: S. 150-154
T. Kobata, K. Ide, H. Kajikawa, W. Sabuga, S. Scheppner und W. Schultz
Final report on supplementary comparison APMP.M.P-S8 in hydraulic gauge pressure from 100 MPa to 1000 MPa, Tech. Suppl., 07009
2010, Metrologia 47
O. Jusko, M. Neugebauer, H. Reimann, W. Sabuga und T. Priruenrom
Dimensional calibration techniques for pressure balances to be used in the new determination of the Boltzmann constant. CD Proceedings of I CIMMEC – 1st International Congress on Mechanical Metrology, Rio de Janeiro, Brazil, October 8-10, 2008
2009, Infosim – Informative Bulletin of the Interamerican Metrology System – OAS : S. 14-23
O. Jusko, D. Bastam, M. Neugebauer, H. Reimann, W. Sabuga und T. Priruenrom
Final results of the geometrical calibration of the pressure balances to be used for the new determination of the Boltzmann constant
2009, Proceedings of the 9th International Symposium on Measurement Technology and Intelligent Instruments (ISMTII-2009), Saint-Petersburg, Russia
B. Fellmuth, J. Fischer, C. Gaiser, T. Priruenrom, W. Sabuga und P. Ulbig
The international Boltzmann project – contribution of PTB
2009, C. R. Physique 10: S. 824-834
T. Bock, H. Ahrendt und K. Jousten
Reduction of the uncertainty of the PTB vacuum pressure scale by a new large area non-rotating piston gauge
2009, Metrologia 46: S. 389-396
Y. Kiselev, W. Sabuga, K. Dapkeviciene, P. Farar, K. Saczuk und I. Sandu
Final report on key comparison COOMET.M.P-K1 in the range 0.05 MPa to 0.5 MPa of pneumatic gauge pressure
2008, Metrologia 45
W. Sabuga und J. Forastieri
Final report on comparison EURAMET.M.P-S6 of PTB and INTI pressure standards for the range 1.5 kPa to 300 kPa of absolute gas pressure. Tech. Suppl., 07020
2008, Metrologia 45
W. Sabuga
Druckmessung von Kilo- bis Gigapascal
2008, PTB-Mitteilungen 118 (3): S. 170-174
M. Rantanen, S. Semenoja, M. Ackerholm, A. Condereys, Z. Krajíček, W. Sabuga, J. Verbeek und C. Wüthrich
High pressure comparison between seven European National Laboratories, Range 50 MPa to 500 MPa, Report on EUROMET Project 881
2007, Metrologia
W. Sabuga
Towards 7 MPa pressure standards with 1 10-6 uncertainty
2007, MAPAN - J. of Metrology Society of India 22 (1): S. 3-11
W. Sabuga und T. Priruenrom
An approach to the evaluation of dimensional measurements on pressure-measuring piston-cylinder assemblies
2007, Proceedings of the 3rd Conference on Pressure Measurement IMEKO TC16, Merida, Mexico
http://www.imeko.org/publ.../IMEKO-TC16-2007-074u.pdf
W. Sabuga
Development of pressure balances for measurement of absolute pressures up to 7 MPa with an uncertainty of 1·10-6
2006, PTB-Bericht PTB-Th-3

Bemerkung: Talks of the 221st PTB Seminar "Workshop on Progress in Determining the Boltzmann Constant" held on 19th October 2006 in Berlin
W. Sabuga, G. Molinar, G. Buonanno, T. Esward, J. C. Legras und L. Yagmur
Finite element method used for calculation of the distortion coefficient and associated uncertainty of a PTB 1GPa pressure balance – EUROMET project 463
2006, Metrologia 43: S. 311-325
W. Sabuga, G. Molinar, G. Buonanno, T. Esward, T. Rabault und L. Yagmur
Calculation of the distortion coefficient and associated uncertainty of PTB and LNE 1 GPa pressure balances using finite element analysis – EUROMET project 463
2005, Metrologia 42: S. 202-206
G. Molinar, M. Bergoglio, W. Sabuga, P. Otal, G. Ayyildiz, J. Verbeek und P. Farar
Calculation of effective area A0 for six piston-cylinder assemblies of pressure balances. Results of the EUROMET Project 740
2005, Metrologia 42: S. 197-201
W. Sabuga und O. Jusko
The effect of piston-cylinder gap geometry on the pressure distortion coefficient of pressure balances
2003, Acta Metrologica Sinica Press : S. 44-59

Bemerkung: Proceedings of International Symposium on Pressure and Vacuum, IMEKO TC16, Beijing, September 22-24
W. Sabuga
Determination of the pressure distortion coefficient of pressure balances using a modified experimental method
2002, Proceedings of NCSL International Workshop and Symposium, San Diego : S. 17 p.
J. Jäger und W. Sabuga
Establishment of a primary standard for the 1 GPa range of pressure measurement
2001, Proceedings of the 2nd International Pressure Metrology Workshop & International Conference on High Pressure Science and Technology, New Delhi : S. 15-20
W. Sabuga
Determination of elastic properties of piston gauges using the strain gauge method. Proceedings of the 17th International Conference on Force, Mass, Torque and Pressure Measurements
2001, IMEKO TC3 : S. 380-385
J. Jäger, W. Sabuga und D. Wassmann
Piston-cylinder assemblies of 5 cm2 cross-sectional area used in an oil-operated primary pressure balance standard for the 10 MPa range
1999, Metrologia 36(6): S. 541-544
G. Molinar, W. Sabuga, G. Robinson und J. C. Legras
Comparison of methods for calculating distortion in pressure balances up to 400 MPa - EUROMET Project #256
1998, Metrologia 35: S. 739-759
J. Jäger, G. Schoppa und W. Schultz
The standard instruments of the PTB for the 1 GPa range of pressure measurement
1996, PTB-Report
W. Sabuga
Elastic distortion calculations at PTB on a PTB 400 MPa pressure balance as part of EUROMET Project 256
1995, PTB-Report W-60
J. Jäger
Use of a Precision Mercury Manometer with Capacitance Sensing of the Menisci
1993, Metrologia 30: S. 553-558
G. Klingenberg und J. C. Legras
Bilateral Comparative Pressure Measurements of the LNE and the PTB Using 10 cm2 Piston-Cylinder-Assemblies
1993, Metrologia 30: S. 603-606
H. Ahrendt
Vergleichsmessungen von Tauchglockenmanometern
1992, PTB-Mitteilungen 102 (6): S. 463-466
J. Jäger, G. Klingenberg und W. Schultz
The Standard Instruments of the PTB for the 5 MPa Range of Pressure Measurement
1990, PTB-Mitteilungen 100 (6): S. 429-438
J. Jäger und W. Schultz
Druckvergleichsmessungen zwischen einem Quecksilber-Präzisionsmanometer und Tauchglockenmanometern zur Messung kleiner Überdrücke
1988, PTB-Mitteilungen 98 (1): S. 39-44

Bemerkung: Herrn Professor Dr. Sigmar German zum 60. Geburtstag gewidmet
A. Bandyopadhyay, P. Hilsch und J. Jäger
Use of Controlled-Clearance High-Pressure Balances with Highly Viscous Pressure Transmitting Media
1987, PTB-Mitteilungen 97 (4): S. 264-270
G. Klingenberg
The Theory of the Flow in a Converging Channel Applied to Piston-Cylinder Systems of Pressure Balances
1987, Metrologia 24: S. 89-95
G. Klingenberg
Elastic Distortion of Piston-Cylinder Systems of Pressure Balances
1986, Metrologia 22: S. 259-263
G. Klingenberg
Die Normalmesseinrichtung der PTB zur Messung kleiner Differenzen hoher statischer Drücke PTB's standard measuring facility for the measurement of small differences in high static pressures
1983, PTB-Mitteilungen 93 (1): S. 1-8
J. Jäger
DMS-Druckaufnehmer als Transfer-Normalgeräte bei Hochdruck-Vergleichsmessungen
1983, PTB-Mitteilungen 93 (2): S. 95-96
J. Jäger, G. Klingenberg und W. Schultz
The PTB Standard Pressure Balance for the 100 MPa Range of Measurement
1982, PTB-Mitteilungen 92 (5): S. 321-327
G. Klingenberg
Untersuchung der Langzeitstabilität einiger Manganinmanometer
1981, PTB-Mitteilungen 91 (1): S. 33-35
Seite:  
Zurück | 1, 2 | Weiter